Back to group list

Back to OSM-IN Decision Sheets Group type of document list

OSM-IN Decision Sheets GROUP | OSM-IN DECISION SHEETS

Consultation & Downloading

Click on the document for preview:
  • 1*: [x] Documents needed for the next meeting
  • 2*: [✓] Tick case for downloading
  • Red printing: newly available or updated documents published within the last three months

Search document

Error: select one or more document.
Done: You file will be sent for downloading.

Document table

1* Document owner Reference number Issuing date Upload date Status Category Standards Title Download
x OSM-IN INDEX 2019-05-06 2019-05-06 Approved General Index_Decision Sheets_OSM-IN_CTL_IS_2019-05-6
  OSM IN OSM-IN-288 2019 2019-06-03 Approved INST EN 61643 series, EN 50539 series Residual voltage measurement
x OSM IN OSM-IN-287 2019 2019-06-03 Approved INST EN 60320-1:2015, EN 60999-1:2000 Cross sectional larea of conductors
  OSM-IN OSM-IN-285 2018 2018-02-06 Approved INST EN 60669-2-1:2002, EN 60669-2-1:2002/A1 Abnormal conditions
  OSM-IN OSM-IN-283 2018 2018-02-06 Approved INST EN 61439-1:2011, ISO 179, EN 62208:2011 - Resistance to ultra-violet (UV) - 70% retention minimum - Charpy impact
  OSM-IN OSM-IN-282 2018 2018-02-06 Approved INST EN 61008-1:2012 Simplified test procedures
  OSM-IN OSM-IN-281 2018 2018-02-06 Approved INST EN 60669-1:1999, EN 60669-1:1999/A1:2002, EN 60669-1:1999/A2:2008 Pilot lamp
  OSM-IN OSM-IN-280 2015 2016-05-02 Approved POW EN 60947-1 Classification of terminal concerning the material composition
  OSM-IN OSM-IN-279 2015 2016-05-02 Approved PROT EN 60898-1 A13 Where to apply the metal foil on the outer surface of the housing of the circuit breaker for the dielectric test
  OSM-IN OSM-IN-278 2015 2016-05-02 Approved POW EN 60947-1 Classification of terminal concerning the material composition
  OSM-IN OSM-IN-277 2015 2015-02-18 Approved PROT EN 60898-1 A13 Where to apply the metal foil on the outer surface of the housing of the circuit breaker for the dielectric test
  OSM-IN OSM-IN-276 2015 2015-02-18 Approved PROT EN 61009-1 Cross section of flexible cables, used for the short-circuit tests
  OSM-IN OSM-IN-275 2015 2015-02-18 Approved PROT EN 61008-1 Cross section of flexible cables, used for the short-circuit tests
  OSM-IN OSM-IN-274 2015 2016-05-02 Approved General EN 60384-14 OSM/IN 274
  OSM-IN OSM-IN-273 2015 2016-05-02 Approved CONT IEC 60730-1, ed.4 Creepage distances
  OSM-IN OSM-IN-272 2015 2016-05-02 Approved PROT EN 50539-11:2013, EN 61643-11: 2012 Generator specification for the measurement of the Front Wave Sparkover Voltage
  OSM-IN OSM-IN-271 2014 2014-05-04 Approved PROT EN 50539-11:2013 Power source requirements for testing
  OSM-IN OSM-IN-270 2014 2014-05-04 Approved PROT EN 50539-11:2013 Correct sample preparation and application of the overload behaviour test
  OSM-IN OSM-IN-269 2014 2014-05-04 Approved PROT EN 61643-11:2012 Sample preparation for thermal stability test
  OSM-IN OSM-IN-268 2014 2014-01-31 Approved INST EN 50075:1990, EN 60320-1:2001, EN 60320-1:2001/A1:2007, EN 60320-2-2:1998, EN 61058-2-1:2011 Flexible cords with textile braiding used in non-rewirable products
  OSM-IN OSM-IN-267 2015 2016-05-03 Approved General General OSM-IN 267
  OSM-IN OSM-IN-266 2013 2013-05-17 Approved INST EN 61242:1997, EN 61242:1997/A1:2008 Trip-free mechanism of cut-outs in cable-reels
  OSM-IN OSM-IN-265 2013-12-27 Approved INST EN 60669-1:1999, EN 60669-1:1999/A1:2002, EN 60669-1:1999/A2:2008 Screwless terminals with two clamping units and one unlock lever
  OSM-IN OSM-IN-264 2013 2013-04-16 Approved INST EN 60998-1:2004 Suitable metals given in the standard - e.g. copper and alloy consisting of 58% or 50% copper
  OSM-IN OSM-IN-263 2012 2013-03-24 Approved General General Test of indelibility of marking (aliphatic solvent)
  OSM-IN OSM-IN-262 2013 2013-03-01 Approved INST EN 60320-1:2001, EN 60320-1:2001/A1:2007 Protruding wall on appliance inlets according to Standard Sheet C8
  OSM-IN OSM-IN-261 2011 2011-10-18 Approved PROT EN 60898-1:2003, EN 60898-1:2003/A1:2004, EN 60898-1:2003/A11:2005 Test voltage applied during the verification of leakage currents across open contacts
  OSM-IN OSM-IN-260 2011 2011-10-18 Approved CONT EN 60730-1:2000, EN 60730-1:2000/A12:2003, EN 60730-1:2000/A1:2004, EN 60730-1:2000/A13:2004, EN 60730-1:2000/A14:2005, EN 60730-1:2000/A15:2007, EN 60730-1:2000/A16:2007, EN 60730-1:2000/A2:2008 Torque applied to terminals mounted on a printed circuit board and what conductor sizes may be specified
  OSM-IN OSM-IN-259 2011 2011-10-18 Approved CONT EN 60730-1:2000, EN 60730-1:2000/A12:2003, EN 60730-1:2000/A1:2004, EN 60730-1:2000/A13:2004, EN 60730-1:2000/A14:2005, EN 60730-1:2000/A15:2007, EN 60730-1:2000/A16:2007, EN 60730-1:2000/A2:2008 Type of insulation required for a 230 V supplied LED with its top surface accessible with the test finger
  OSM-IN OSM/IN 258A 2015 2016-05-02 Approved PROT EN 61009-1 Cross section of flexible cables, used for the short-circuit tests
  OSM-IN OSM-IN-258 2011 2011-10-18 Approved CONT EN 60730-1:2000, EN 60730-1:2000/A12:2003, EN 60730-1:2000/A1:2004, EN 60730-1:2000/A13:2004, EN 60730-1:2000/A14:2005, EN 60730-1:2000/A15:2007, EN 60730-1:2000/A16:2007, EN 60730-1:2000/A2:2008 Application of Table H.27.1 in case of approved capacitors
  OSM-IN OSM-IN-257C 2013 2013-12-27 Approved INST EN 60670-1:2005 Technical Report on flush-mounting boxes covered by CLC/TC 23BX used by CENELEC members and affiliate member countries (INFORMATIVE)
  OSM-IN OSM-IN-256 2011 2011-10-18 Approved PROT EN 60898-1:2003, EN 60898-1:2003/A1:2004, EN 60898-1:2003/A11:2005 Reference values for the classification of CBs into energy limiting classes
  OSM-IN OSM-IN-255 2011 2011-10-18 Approved PROT EN 61009-1:2004, EN 61009-1:2004/A11:2008, EN 61009-1:2004/A12:2009, EN 61009-1:2004/A13:2009 Reference values for the classification of RCBOs into energy limiting classes
  OSM-IN OSM-IN-254 2011 2011-10-18 Approved INST EN 60670-1:2005 Classification of flush-mounting boxes according to clause 7, Table 1, and consequent applicability of clause 15 “Mechanical tests”
  OSM-IN OSM-IN-253 2011 2011-10-18 Approved INST EN 60669-1:1999, EN 60669-1:1999/A1:2002 Lamps to be used instead of 200 W tungsten filament lamps
  OSM-IN OSM-IN-252 2011 2012-04-30 Approved CONT EN 60730-1:2000, EN 60730-1:2000/A12:2003, EN 60730-1:2000/A1:2004, EN 60730-1:2000/A13:2004, EN 60730-1:2000/A14:2005, EN 60730-1:2000/A15:2007, EN 60730-1:2000/A16:2007, EN 60730-1:2000/A2:2008 Resetting of control after voltage dip test
  OSM-IN OSM-IN-251 2010 2011-10-18 Approved CONT EN 60730-1:2000, EN 60730-1:2000/A12:2003, EN 60730-1:2000/A1:2004, EN 60730-1:2000/A13:2004, EN 60730-1:2000/A14:2005, EN 60730-1:2000/A15:2007, EN 60730-1:2000/A16:2007, EN 60730-1:2000/A2:2008 Behaviour of a protection device during heating test
  OSM-IN OSM-IN-250 2010 2011-10-18 Approved CONT EN 60670-1:2005 Impact test on boxes provided with knock-outs
  OSM-IN OSM-IN-249 2010 2011-10-18 Approved INST EN 60998-2-1:2004 Applicable standards to connecting devices for flexible cords
  OSM-IN OSM-IN-248 2010 2011-10-18 Approved General General Mandatory additional information (details) in Test Report
  OSM-IN OSM-IN-247 2010 2011-10-18 Approved PROT EN 60898-1:2003 Test voltage
  OSM-IN OSM-IN-246 2010 2011-10-18 Approved PROT EN 61009-1:2004 Inconsistency regarding the test current In instead of 1,13 In
  OSM-IN OSM-IN-245 2010 2011-10-18 Approved PROT EN 61009-1:2004 Missing requirements for r.c. units declared not suitable for disassembling
  OSM-IN OSM-IN-244 2010 2011-10-18 Approved INST EN 60309-2:1999, EN 60309-2:1999/A1:2007 Construction of pins of plugs and appliance inlets
  OSM-IN OSM-IN-243 2010 2011-10-18 Approved INST EN 61058-1:2002, EN 61058-1:2002/A2:2008 Rotary switches for “cooking range” (Endurance test)
  OSM-IN OSM-IN-242A 2011 2011-10-18 Approved INST EN 61058-1:2002, EN 61058-1:2002/A2:2008 Rotary switches for �cooking range� (Classification and endurance test specifications)
  OSM-IN OSM-IN-241 2008 2011-10-18 Approved INST EN 60669-1:1999, EN 60669-1:1999/A1:2002 Verification of non-removal of covers, cover plates or actuating members
  OSM-IN OSM-IN-240 2008 2011-10-18 Approved INST EN 60669-1:1999, EN 60669-1:1999/A1:2002 Simplification of making and breaking capacity and normal operation tests
  OSM-IN OSM-IN-239 2008 2011-10-18 Approved INST EN 60669-1:1999, EN 60669-1:1999/A1:2002 Correct positioning of conductors
  OSM-IN OSM-IN-238 2008 2011-10-18 Approved INST EN 60669-1:1999, EN 60669-1:1999/A1:2002 Inlet opening of surface-type switches
  OSM-IN OSM-IN-237 2008 2011-10-18 Approved INST EN 61386-21:2004, EN 61386-22:2004, EN 61386-23:2004 Certification procedure for conduits and conduit fittings
  OSM-IN OSM-IN-236 2008 2011-10-18 Approved INST EN 61058-2-1:1993, EN 61058-2-1:1993/A1:1996, EN 61058-2-1:1993/A11:2002 Fixing of the housing of non-rewirable switches
  OSM-IN OSM-IN-235 2008 2011-10-18 Approved INST EN 61058-2-1:1993, EN 61058-2-1:1993/A1:1996, EN 61058-2-1:1993/A11:2002 Pull test and following torque test on non-rewirable switches
  OSM-IN OSM-IN-234 2008 2011-10-18 Approved INST EN 61058-2-1:1993, EN 61058-2-1/A1:1996, EN 61058-2-1/A11:2002 Type of attachment of flexible cords
  OSM-IN OSM-IN-233 2008 2011-10-18 Approved INST EN 60670-1:2005 Definition of �reverse tapers�
  OSM-IN OSM-IN-232 2008 2011-10-18 Approved INST EN 61534:2003 Classification of socket-outlet used in combination with power track system
  OSM-IN OSM-IN-230 2008 2011-10-18 Approved INST EN 60670-1:2005 Positioning of the dry absorbent paper and the strip of paper for IP tests
  OSM-IN OSM-IN-229 2008 2011-10-18 Approved INST EN 61058-1:2002 T-marking and heating test
  OSM-IN OSM-IN-228 2008 2011-10-18 Approved INST EN 60998-2-2:2004 Accepting of a smaller range of cross-sectional areas
  OSM-IN OSM-IN-227 2008 2011-10-18 Approved INST EN 61386-21:2004 Testing programme for a range of conduit sizes
  OSM-IN OSM-IN-226 2008 2011-10-18 Approved INST EN 60669-2-1:2004 Testing of electronic switches without incorporated fuses/ without incorporated limiting device
  OSM-IN OSM-IN-223 2008 2011-10-18 Approved INST EN 60669-1:1999 EN 60669-1:1999/A1:2002 Terminals connecting capacity for rated current up to 4 A
  OSM-IN OSM-IN-222 2008 2011-10-18 Approved INST EN 60320-1:2001EN 60320-1:2001/A1:2007 Withdrawal force test
  OSM-IN OSM-IN-221 2008 2011-10-18 Approved INST EN 60320-1:2001 Test voltage for appliance couplers
  OSM-IN OSM-IN-220 2008 2011-10-18 Approved INST EN 60320-1:2001EN 60320-1:2001/A1:2007 Certification of non-rewirable connector intended for use as a part of a cord set or an interconnection cord set
  OSM-IN OSM-IN-219 2008 2011-10-18 Approved INST EN 62208:2003 Impact test in knock-outs
  OSM-IN OSM-IN-218B 2011 2011-10-18 Approved PROT EN 60898-1:2003, EN 61008-1:2004, EN 61009-1:2004 Resistance to abnormal heat and to fire (glow-wire test)
  OSM-IN OSM-IN-217 2008 2011-10-18 Approved PROT EN 60898-1:2003EN 60898-1:2003/A1:2004, EN 60898-1:2003/A11:2005, EN 60947-2:2006 Markings of circuit breakers, certified according to EN 60898-1 and EN 60947-2 standards
  OSM-IN OSM-IN-216 2008 2011-10-18 Approved INST EN 60669-2-1:2004 Electronic switch multi-layer printed wire board creepage and clearance distances
  OSM-IN OSM-IN-215 2008 2011-10-18 Approved INST EN 60669-2-1:2004, Temperature rise on cover surfaces of a dimmer switch - Use of standardized boxes for the Temperature rise test
  OSM-IN OSM-IN-214B 2011 2011-10-18 Approved PROT EN 61009-1:2004, Test of instantaneous tripping and of correct opening of the contacts
  OSM-IN OSM-IN-213 2008 2011-10-18 Approved PROT EN 61643-11:2002, EN 61643-11:2002/A11:2007 Markings
  OSM-IN OSM-IN-212 2008 2011-10-18 Approved PROT EN 61643-11:2002, EN 61643-11:2002/A11:2007 Measured limiting voltage
  OSM-IN OSM-IN-211 2007 2011-10-18 Approved CONT EN 60730-2-9:2000, EN 60730-2-9:2000/A1:2003, EN 60730-2-9:2000/A11:2003, EN 60730-2-9:2000/A12:2004, EN 60730-2-9:2000/A2:2005 Conection of the load to manual reset thermal cut-outs
  OSM-IN OSM-IN-210 2007 2011-10-18 Approved CONT EN 60730-1:2000, EN 60730-1:2000/A12:2003, EN 60730-1:2000/A1:2004, EN 60730-1:2000/A13:2004, EN 60730-1:2000/A14:2005, EN 60730-1:2000/A15:2007, EN 60730-1:2000/A16:2007 Capacitors used for protective impedance
  OSM-IN OSM-IN-209 2007 2011-10-18 Approved INST EN 60669-1:1999, EN 60669-1:1999/A1:2002 Resistance to insulation material to abnormal heat and to fire
  OSM-IN OSM-IN-208 2007 2011-10-18 Approved PROT EN 61009-1:2004 Clarification of the text
  OSM-IN OSM-IN-207 2007 2011-10-18 Approved PROT EN 61008-1:2004 Clarification of the text
  OSM-IN OSM-IN-204 2007 2011-10-18 Approved PROT EN 61643-11:2002 Issue of CCA-STR for plug in surge protector within CCA Agreement
  OSM-IN OSM-IN-203 2007 2011-10-18 Approved INST EN 60799:1998, CCA-NTRs for cord sets
  OSM-IN OSM-IN-202A 2013 2013-12-27 Approved INST EN 50075:1990, Coil incorporated in 2.5 A Europlugs
  OSM-IN OSM-IN-201 2007 2011-10-18 Approved INST EN 60309-2:1999, Measuring of height of retaining means for IP44 socket-outlets and connectors
  OSM-IN OSM-IN-140 2000 2011-10-18 Approved CONT EN 60730-2-14:1997 Symbol for class II construction
  OSM-IN OSM-IN-139 2000 2011-10-18 Approved CONT EN 60730-2-9:2002 Control declared as sensing element
  OSM-IN OSM-IN-138 2000 2011-10-18 Approved CONT EN 60730-1:2000 Conductive pollution described in clause N.1
  OSM-IN OSM-IN-137 2000 2011-10-18 Approved CONT EN 60730-1:2000 A cable or cord to an external SELV sensor
  OSM-IN OSM-IN-134 2000 2011-10-18 Approved CONT EN 60730-1:2000 Additional tests for automatic electrical controls with Tmax below 0 �C
  OSM-IN OSM-IN-133 1999 2011-10-18 Approved CONT EN 60730-1:2000, Verification of the protection against overloading for in-line controls
  OSM-IN OSM-IN-132 1994 2011-10-18 Approved CONT EN 60730-1:2000, Criteria for obtaining an intermediate position of an actuating member
  OSM-IN OSM-IN-131 1999 2011-10-18 Approved CONT EN 60730-1:1995 Verification of the protection against overloading for in-line controls
  OSM-IN OSM-IN-126 2001 2011-10-18 Approved INST EN 61058-2-1:1993, EN 61058-2-1/A1:1996 Pull testing and following torque test of non-rewirable switches
  OSM-IN OSM-IN-125 1999 2011-10-18 Approved INST EN 61058-2-1:1993, EN 61058-2-1/A1:1996 Fixing of the housing of non-rewirable switches
  OSM-IN OSM-IN-122 1997 2011-10-18 Approved INST EN 61058-1:1992 Suitability of non-metallic material through which contact pressure is transmitted
  OSM-IN OSM-IN-121 1993 2011-10-18 Approved INST EN 61058-1:1992 Over voltage test
  OSM-IN OSM-IN-120 1993 2011-10-18 Approved INST EN 61058-1:1992 Test voltage
  OSM-IN OSM-IN-119 1992 2011-10-18 Approved INST EN 61058-1:1992 Flat quick-connect terminations
  OSM-IN OSM-IN-118 1998 2011-10-18 Approved INST EN 61058-1:1992 Terminals for prepared copper conductors requiring the use of a special purpose tool
  OSM-IN OSM-IN-112B 1998 2011-10-18 Approved INST EN 61058-1:1992 Sample selection for test on homogeneous series of switches
  OSM-IN OSM-IN-111 1995 2011-10-18 Approved PROT EN 61009-1:1994 Uniform interpretation of sub-clause G.4.4.d)
  OSM-IN OSM-IN-109 1995 2011-10-18 Approved PROT EN 61009-1:1994 Electrical compatibility
  OSM-IN OSM-IN-108 1995 2011-10-18 Approved PROT EN 61009-1:1994 Mechanical requirements
  OSM-IN OSM-IN-107 1995 2011-10-18 Approved PROT EN 61009-1:1994 Constructional requirements
  OSM-IN OSM-IN-106 1995 2011-10-18 Approved PROT EN 61009-1:1994 Marking of RCBO’s
  OSM-IN OSM-IN-105B 2007 2011-10-18 Approved PROT EN 61009-1:1994 EMC Testing for RCBO?s
  OSM-IN OSM-IN-102B 2007 2011-10-18 Approved PROT EN 61008-1:1994 EMC Testing for RCCB�s
  OSM-IN OSM-IN-101 1995 2011-10-18 Approved PROT EN 61008-1:1994 Testing of RCCB�s of different classification due to behaviour to DC components
  OSM-IN OSM-IN-094 2000 2011-10-18 Approved POW EN 60947-3:1999 Test forces for actuators
  OSM-IN OSM-IN-087 1996 2011-10-18 Approved CONT EN 60730-1:1995 Electronic controls declared as �no protection� according to Table 7.1, Item 58a
  OSM-IN OSM-IN-086 1997 2011-10-18 Approved CONT EN 60730-1:1995 Clarification of the Standard text
  OSM-IN OSM-IN-085 2000 2011-10-18 Approved CONT EN 60730-1:1995 Double-break electrical control definition
  OSM-IN OSM-IN-084 1997 2011-10-18 Approved CONT EN 60730-1:1995 Suitability of non-metallic material through which contact pressure is transmitted
  OSM-IN OSM-IN-083 2000 2011-10-18 Approved CONT EN 60730-1:1995, Additional tests for automatic electrical controls with Tmax below 0 �C
  OSM-IN OSM-IN-082 1993 2011-10-18 Approved CONT EN 60730-1:1995, Clarification of the interpretation of the standard
  OSM-IN OSM-IN-081 1993 2011-10-18 Approved CONT EN 60730-1:1995 Current-carrying parts made of copper or brass
  OSM-IN OSM-IN-080 2000 2011-10-18 Approved CONT EN 60730-1:1995, T-marked independently mounted controls
  OSM-IN OSM-IN-079 2002 2011-10-18 Approved CONT EN 60730-1:1995, Maximum temperature permitted on Table 14.1 for materials used other than for wires
  OSM-IN OSM-IN-078 1995 2011-10-18 Approved CONT EN 60730-1:1995, Maximum temperature in terminals of T-marked controls
  OSM-IN OSM-IN-077 1997 2011-10-18 Approved CONT EN 60730-1:1995, Dimensional requirements for for flat push-on terminals
  OSM-IN OSM-IN-076 1995 2011-10-18 Approved CONT EN 60730-1:1995, Dimension “e” on clamping screw terminals
  OSM-IN OSM-IN-075 1997 2011-10-18 Approved CONT EN 60730-1:1995, Interpretation of the upper limits
  OSM-IN OSM-IN-074 1993 2011-10-18 Approved CONT EN 60730-1:1995, Printed leaflet or specification sheet
  OSM-IN OSM-IN-073 1998 2011-10-18 Approved CONT EN 60730-1:1995, Circuit for declared specific load
  OSM-IN OSM-IN-072 1994 2011-10-18 Approved CONT EN 60730-1:1995 �OFF� Marking on electronic controls
  OSM-IN OSM-IN-071 1993 2011-10-18 Approved CONT EN 60730-1:1995 Identification of materials of construction
  OSM-IN OSM-IN-070 1996 2011-10-18 Approved CONT EN 60730-2-10:1995 Motor starting relays test arrangements
  OSM-IN OSM-IN-069 1997 2011-10-18 Approved CONT EN 60730-2-10:1995 Heating test
  OSM-IN OSM-IN-068 1997 2011-10-18 Approved CONT EN 60730-2-8:1995 Interpretation of Item 9 of the arrangement for measurement of transient pressure caused by electrovalves
  OSM-IN OSM-IN-067 2001 2011-10-18 Approved CONT EN 60730-2-7:1991, EN 60730-2-7:1991/A11:1994, EN 60730-2-7:1991/A12:1993, EN 60730-2-7:1991/A1:1997 Over voltage test
  OSM-IN OSM-IN-066 1997 2011-10-18 Approved CONT EN 60730-2-4:1993 Creepage distances and clearances across micro-interruption
  OSM-IN OSM-IN-065 1997 2011-10-18 Approved CONT EN 60730-2-3:1992 Creepage distances and clearances across micro-interruption
  OSM-IN OSM-IN-023B 1999 2011-10-18 Approved INST EN 50086-2-4:1994 Testing programme for a range of conduit sizes
  OSM-IN OSM-IN-021 1998 2011-10-18 Approved INST EN 50086-2-4:1994 Certification procedure for conduits and conduit fittings
  OSM-IN OSM-IN-020 1992 2011-10-18 Approved INST EN 50075:1990, Glow-wire test
  OSM-IN OSM-IN-014 1999 2011-10-18 Approved INST EN 50075:1990, Procedure if the constructional requirements are not complied with (gripping surface)
  OSM-IN OSM-IN-005 1993 2011-10-18 Approved General EN 17025:2000 Control of pagination and annexes in test report
  OSM-IN OSM-IN-004 1997 2011-10-18 Approved General Instrument accuracy limits to be considered in CCA testing
  OSM-IN OSM-IN-003 1996 2011-10-18 Approved General Pending matters for more than three meetings
  OSM-IN OSM-IN-002 1993 2011-10-18 Approved General Identification of series in test reports
  OSM-IN OSM-IN-001 1992 2011-10-18 Approved General INST Locking device for rivets serving as electrical as well as mechanical connections